The Next Generation in Interior Floor Coatings
WearMax:
ECO Friendly, LEED Approved,  
waterborne floor coatings by KraGil Inc.

Stains

  • Site applied water based
  • Non-Ceramic product
  • Water borne technology
  • Spread rate 300-400 sq ft hand rubbed
  • Spread rate buffed 500-800 sq ft
  • "Stand up" application
  • Low Odor
  • VOC (<235)
  • Dries in 2-3 hours
  • Easy clean up - no oily rags
  • Goes on standing up
  • No more noxious fumes
  • Looks great - even on maple
  • 12 color selection - plus a neutral
  • Custom color program
Color Samples


 
  • Sunset 6910-2001
 
  
 
 
 
  •  Cherry 6910-3001
 
 
 
 
 
  • Mahogany 6910-3002

  • Tabacco DISCONTINUED
 
 

 
  • Canyon 6910-8002
 
 
 
 
 
  • Terra 6910-8003
 
 
 
 
 
  • Harvest 6910-8004
 
 
 
 
 
  • Golden Brown 6910-8005

 
  • Umbra 6910-8006
 
 
 
 
 
  • Antique Brown 6910-8007
 
 
 
 
 
  • Ebony 6910-8008
 
 
 
 
 
  • Ivory 6910-9001

Stain

Waterborne Wood Floor Finishing System

Application Instructions

 

FLOOR PREPARATION (For all staining methods listed):

1.      Sand entire floor as recommended by NOFMA.

2.      Vacuum up all dust and remove all dust sources completely.

3.      Tack entire floor with dry towel until all dust is removed.

NOTE: Test stain on hidden area to verify desired color.  Wood grain variations, sanding and stain application method will affect stain color.

STIR STAIN BEFORE AND DURING USE.

 

BUFFER APPLICATION INSTRUCTIONS:

EQUIPMENT AND MATERIAL:

6910 WearMax Stain

TAP1 T-Bar, TAP2 T-Bar Sleeve or TAP3 Trim Pad

Floor Buffer (175 RPM)

White buffing pad

Cotton towels or rags

Burlap bags (optional)

 

BUFFER APPLICATION:

1.      Apply 6910 WearMax Stain in the direction of the grain using the T-Bar or Trim Pad in a snow plow motion.

2.      Buff stain with buffer and white pad until stain is completely buffed in.

3.      Buff corners and edges by hand with cotton towels or rags.

Uneven stained areas can be spot treated by applying stain in light areas and buffing even.  For less grain raise and smoother finish, use burlap bags in place of white pad.

 

WIPING APPLICATION INSTRUCTIONS:

EQUIPMENT AND MATERIAL:

6910 WearMax Stain

TAP1 T-Bar, TAP2 T-Bar Sleeve or TAP3 Trim Pad

Cotton towels or rags

 

WIPING APPLICATION:

1.      Apply WearMax 6910 Stain in the direction of the grain using the T-Bar or Trim Pad in a snowplow motion.

2.      Wipe stain into floor with slightly stain-dampened towel or rag in circular motion, and then wipe stain off with dry towel or rag in the direction of the grain.

3.      Use a digital moisture meter to ensure stain is dry before applying finish (2-3 hours).

4.      For best results buff stain when dry with maroon pad before applying WearMax Ceramic Finishing System or WearMax Starting Line System.

 

Helpful Hint: On soft woods, such as pine, walnut, cherry, etc., Do Not Let Stain Sit Too Long.  Buff out soon after application.




Once Stain is dry, walk on in SOCKED FEET ONLY for first 24 hours!

 

Clean up: Clean applicators thoroughly between coats, using water.